Windows 10 boot menu settings install#
Windows 10 boot menu settings driver#
Windows 10 boot menu settings windows 10#
Windows 10 boot menu settings portable#
Windows 10 boot menu settings Pc#

On the Devices and Peripherals > USB menu, USB Legacy is enabled (checked).

On the Devices and Peripherals > SATA menu, Chipset SATA Mode is set to AHCI.

Tested with the development build at OpenElec.В Check these BIOS settings (and change if necessary)

On the Boot > Boot Configuration menu, in the UEFI Boot pane, OS Selection is set to Windows 7.

Proceed with the installation of the operating system.

On the Boot > Boot Configuration menu, in the UEFI Boot pane, OS Selection is set to Windows 8.x/Windows 10.

On the Boot > Boot Priority menu, in the Legacy Boot Priority pane, Legacy Boot is disabled (unchecked).

On the Devices and Peripherals > SATA menu, Chipset SATA Mode to AHCI.

Press F9 to set all BIOS options to default values.

Press F2 when prompted during boot to enter BIOS Setup.

See the instructions at Install Windows 7* on Computers with USB 3.0.Д¬heck these BIOS settings (and change if necessary):

Don't install Windows 10 on the Intel Optane Memory module. If you plan to install both a hard drive and IntelВ® Optaneв„ў Memory, WindowsВ® 10 must be installed on the hard drive. If your Intel NUC model isn't listed in this table, there are no additional special instructions and you can proceed directly to the installation steps. See the table for special information you should know before you begin installing the operating system.

Get your Windows image ready (purchased separately), on either a USB portable device or on a CD/DVD.Д¬lick or the topic for details: Model-specific information.

Use another computer connected to the Internet to download the latest wired or wireless network driver for your Intel NUC.

Install necessary components in the Intel NUC (memory and drive, purchased separately).

Review the model-specific table below for any special information that applies to your Intel NUC model.

If an operating system was installed in a specific SATAВ operation and then changed later, you will not be able to boot into the OS until the change is reverted.See the Supported Operating Systems for IntelВ® NUC Products for a list of Windows* versions supported by your IntelВ® NUC. NOTE: Ensure that in the Dell BIOS AHCI is selected and not RAID as RAID is default.

Disable Secure boot and Enable after PC is imaged.

HP: Advanced > Remote Management Options >В USB Key Provisioning Support = checked.

USB Key Provisioning Support should be enabled.

Lenovo: Security > TCGВ feature setup > TCGВ Security feature >В TCGВ Security feature = activeВ (May be TPMВ on other Motherboards).

HP: Advanced > TPM Embedded Security > TPM Device = Available TPM State = checked.

DELL: Security > TPM Security > TPM Security (boxed checked) Activate (box checked).

HP: Advanced > Boot Options > Network (PXE) Boot = unchecked.

DELL: System Configuration> Integrated NIC > Integrated NIC = Enabled (change from default value of 'Enabled w/PXE').

HP: Advanced > Boot Options > CD-ROM Boot = unchecked.

Lenovo: Start up > Quick Boot > Quick Boot = disabled.

HP: Advanced > Boot Options > Fast Boot = unchecked.

DELL: POST Behavior > Fastboot > FastbootВ =Thorough.

Lenovo: Start up > CSMВ > CSMВ = disabledВ (May not have CSMВ option on other Motherboards).

Disable CSM (Compatibility Support Module is something that allows booting in legacy BIOS mode on UEFI systems).

Lenovo: Security > Secure Boot >В Secure Boot = enabled.

HP: Advanced > Secure Boot Configuration > Configure Legacy Support and Secure Boot = Legacy Support Disable and Secure Boot Enable.

Enable secure boot, if machine supports it.

Lenovo: Devices > ATAВ Drive Setup > Configure SATAВ as = AHCI.

DELL: System Configuration > SATA Operation > SATA Operation = AHCI.

SATA Operation should be set to AHCI, but only on computers where Windows is being upgraded or re-installed (not applicable to brand new computers).

Lenovo: Start up > Boot mode > Boot mode = UEFIВ only.

HP: Advanced > Boot Options > UEFI Boot Order = checked, and Legacy Boot Order = unchecked Network (PXE) Boot = unchecked.

DELL: General > Boot Sequence > Boot List Option = UEFI Advanced Boot Options > Enable Legacy Option ROMs = unchecked.

Make sure that UEFI boot is enabled and legacy boot disabled.

Escape - get to device configuration menu.

Go through all menu's in the GUIВ and change any related settings. Every BIOS/UEFIВ GUIВ will look different and these are just general points to lookout for.

Windows 10 boot menu settings install#

Windows 10 boot menu settings windows 10#

Windows 10 boot menu settings portable#

Windows 10 boot menu settings driver#

Windows 10 boot menu settings Pc#